Хм, bonding.txt из линуксведра вполне раскрывает эту тему
2) HA on two or more switches (or a single switch without trunking support)
---------------------------------------------------------------------------
This mode is more problematic because it relies on the fact that there
are multiple ports and the host's MAC address should be visible on one
port only to avoid confusing the switches.
If you need to know which interface is the active one, and which ones are
backup, use ifconfig. All backup interfaces have the NOARP flag set.
To use this mode, pass "mode=1" to the module at load time :
# modprobe bonding miimon=100 mode=1
Or, put in your /etc/modules.conf :
alias bond0 bonding
options bond0 miimon=100 mode=1
Example 1: Using multiple host and multiple switches to build a "no single
point of failure" solution.
| |
|port3 port3|
+-----+----+ +-----+----+
| |port7 ISL port7| |
| switch A +--------------------------+ switch B |
| +--------------------------+ |
| |port8 port8| |
+----++----+ +-----++---+
port2||port1 port1||port2
|| +-------+ ||
|+-------------+ host1 +---------------+|
| eth0 +-------+ eth1 |
| |
| +-------+ |
+--------------+ host2 +----------------+
eth0 +-------+ eth1
In this configuration, there are an ISL - Inter Switch Link (could be a trunk),
several servers (host1, host2 ...) attached to both switches each, and one or
more ports to the outside world (port3...). One an only one slave on each host
is active at a time, while all links are still monitored (the system can
detect a failure of active and backup links).
Each time a host changes its active interface, it sticks to the new one until
it goes down. In this example, the hosts are not too much affected by the
expiration time of the switches' forwarding tables.
If host1 and host2 have the same functionality and are used in load balancing
by another external mechanism, it is good to have host1's active interface
connected to one switch and host2's to the other. Such system will survive
a failure of a single host, cable, or switch. The worst thing that may happen
in the case of a switch failure is that half of the hosts will be temporarily
unreachable until the other switch expires its tables.
Example 2: Using multiple ethernet cards connected to a switch to configure
NIC failover (switch is not required to support trunking).
+----------+ +----------+
| |eth0 port1| |
| Host A +--------------------------+ switch |
| +--------------------------+ |
| |eth1 port2| |
+----------+ +----------+
On host A : On the switch :
# modprobe bonding miimon=100 mode=1 # (optional) minimize the time
# ifconfig bond0 addr # for table expiration
# ifenslave bond0 eth0 eth1
Each time the host changes its active interface, it sticks to the new one until
it goes down. In this example, the host is strongly affected by the expiration
time of the switch forwarding table.
3 октября 2010 г. 23:52 пользователь Michael Bochkaryov
Мое почтение всем!
Не подскажет ли кто направление копания в такой задаче?
Имеется: 1) 2 сервера на linux c 2 x ethernet 2) 2 управляемых свича с поддержкой link aggregation 802.3ad
Нужно организовать "шибко надежный" ethernet для парочки серверов. Чтобы как при вылете порта, так и при вылете одного из свичей сетка продолжала работать, пускай и с меньшей скоростью.
Можно ли link aggregation организовать на портах в разных свичах? Или нужно на уровне IP это разруливать (чего не хочется)?
Заранее спасибо :)
-- Regards, Michael Bochkaryov Net.Style - VoIP and VAS development www.netstyle.com.ua
-- Yours, Max