Задам еще один вопрос. Стояла в лабе 7604 с одной платой CXL, я выдернул из работающего шасси резервный модель и перекинул его в лабу. При этом режим redundancy сконфигурирован как SSO. Но после загрузки подброшенной платы я получаю переход в RPR: Jan 26 11:37:03.638 EET: %ISSU-SP-3-INCOMPATIBLE_PEER_UID: Peer image (c7600rsp72043_sp-ADVIPSERVICESK9-M), version (12.2(33)SRB2) on peer uid (2) is incompatible Jan 26 11:37:22.246 EET: %PFREDUN-SP-4-INCOMPATIBLE: Defaulting to RPR mode (Runtime incompatible) Jan 26 11:37:27.841 EET: %FABRIC-SP-5-CLEAR_BLOCK: Clear block option is off for the fabric in slot 2. Jan 26 11:37:27.925 EET: %FABRIC-SP-5-FABRIC_MODULE_BACKUP: The Switch Fabric Module in slot 2 became standby Jan 26 11:37:28.561 EET: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimal Diagnostics... Jan 26 11:37:30.062 EET: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics Jan 26 11:37:30.586 EET: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are now online Jan 26 11:39:53.249 EET: %PFREDUN-SP-6-ACTIVE: Standby initializing for RPR mode Jan 26 11:39:53.465 EET: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output. Jan 26 11:39:54.761 EET: %PFINIT-SP-5-CONFIG_SYNC: Sync'ing the startup configuration to the standby Router. Jan 26 11:40:01.953 EET: %RF-SP-5-RF_TERMINAL_STATE: Terminal state reached for (RPR) Какого лешего? IOS ведь загружены одинаковые? Redundant System Information : ------------------------------ Available system uptime = 7 weeks, 3 days, 15 hours, 38 minutes Switchovers system experienced = 2 Standby failures = 2 Last switchover reason = active unit removed Hardware Mode = Duplex Configured Redundancy Mode = sso Operating Redundancy Mode = rpr Maintenance Mode = Disabled Communications = Up Current Processor Information : ------------------------------- Active Location = slot 1 Current Software state = ACTIVE Uptime in current state = 7 weeks, 1 day, 20 hours, 13 minutes Image Version = Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 10-Oct-07 08:10 by prod_rel_team BOOT = bootdisk:c7600rsp72043-advipservicesk9-mz.122-33.SRB2.bin,12; CONFIG_FILE = BOOTLDR = Configuration register = 0x2102 Peer Processor Information : ---------------------------- Standby Location = slot 2 Current Software state = STANDBY COLD Uptime in current state = 3 minutes Image Version = Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB2, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 10-Oct-07 08:10 by prod_rel_team BOOT = bootdisk:c7600rsp72043-advipservicesk9-mz.122-33.SRB2.bin,12; CONFIG_FILE = BOOTLDR = Configuration register = 0x2102 Не сталкивались с таким поведением? =================================================================== uanog mailing list. To Unsubscribe: send mail to majordomo@uanog.kiev.ua with "unsubscribe uanog" in the body of the message